DENO LED Lighting

Fitas de LED Longas | 65.6ft e 100ft | DENO

A série de Fitas de LED para trechos ultralongos da DENO LED oferece comprimentos contínuos estendidos, minimizando os pontos de injeção de alimentação e simplificando as instalações para aplicações B2B. Essas Fitas de LED de 24V apresentam alto IRC (CRI) (Ra>90) para reprodução precisa das cores, com densidades de potência de até 19.2 W/m. Utilizando FPCB eletrodepositado em processo rolo a rolo e interconexões com fio de ouro de 99.99% de pureza, garantem confiabilidade. Disponíveis em diversos graus de proteção IP, são adequadas para iluminação arquitetônica, iluminação de sancas e projetos comerciais de grande escala que exigem iluminação contínua em distâncias significativas.

Long LED Strip Lights models & key specifications (4)

8466 — 2835 · 60 LEDs/m · 24V

8466 long led strip — 24V, cuttable every 166.7mm, 10mm FPCB width, 2835 LEDs, 60 LEDs/m, IP20

LED Type: 2835 · LED Density: 60LEDs/m · Voltage: 24V · Cutting Unit: 10LEDs/166.66mm · PCB Width: 10mm · Copper Foil: 3oz · Circuit Type: C.C. · IP Rating: IP20

7909 — 2835 · 120 LEDs/m · 24V

7909 long led strip — 24V, cuttable every 41.7mm, 8mm FPCB width, 2835 LEDs, 120 LEDs/m, IP20

LED Type: 2835 · LED Density: 120 · CRI: Ra≥80 · Voltage: 24V · Power: 3~35W · Cutting Unit: 5LEDs/41.67mm · PCB Width: 8 · Copper Foil: 3oz · Circuit Type: CC · IP Rating: IP20

7910 — 2835 · 120 LEDs/m · 24V

7910 long led strip — 24V, cuttable every 41.7mm, 10mm FPCB width, 2835 LEDs, 120 LEDs/m, IP20

LED Type: 2835 · LED Density: 120 LEDs/m · CRI: Ra>90 · Voltage: 24V · Cutting Unit: 5LEDs/41.67mm · PCB Width: 10mm · Copper Foil: 3 oz · Circuit Type: C.C. · IP Rating: IP20

14512-N — 2216 · 300 LEDs/m · 24V

14512-N long led strip — 24V, cuttable every 20mm, 10mm FPCB width, 2216 LEDs, 300 LEDs/m, IP20/IP54/IP65/IP66/IP67/IP68

LED Type: 2216 · LED Density: 300 LEDs/m · CRI: Ra≥90 / Ra≥95 · Voltage: DC24V · Power: 6~24W · Cutting Unit: 6LEDs/20mm · PCB Width: 10mm · Copper Foil: 3oz · Circuit Type: CC · IP Rating: IP20/IP54/IP65/IP66/IP67/IP68

Other Fita de LED SMD series

Choose the long LED strip build for the job

  • long led strip lights 24V — Single-colour long runs: 24V constant-current boards in 2700K–6500K, 2 oz to 3 oz copper, 20 m on one feed with no visible fall-off at the far end.
  • long rgb led strip — RGB long runs: Current-regulated colour boards that hold the mix over 15–20 m instead of drifting warm as the red channel starves.
  • long rgbw led strip — RGBW long runs: A dedicated white die alongside the colour trio, so one 20 m board covers architectural white and saturated scenes.
  • long high density led strip — High density long runs: Up to 300 LEDs/m on a long board: dot-free at shallow diffuser depth while still reaching 20 m per feed.
  • 36V long run led strip — 36V long runs: The middle step between 24V and 48V — 30 m class runs on 100 mm cut units where 48V drivers are not available.
  • 48V longest led strip — 48V longest runs: The longest builds DENO makes: up to 50 m from one feed, the practical answer for runs longer than 32 feet.
  • 2216 long led strip — 2216 SMD long runs: Low-profile 2216 emitters on a narrow long board — high CRI, tight pitch, ideal for slim reveals over long distances.
  • 2835 long led strip lights — 2835 SMD long runs: The workhorse: 112, 120, 128 and 288 LEDs/m 2835 boards with constant-current ICs and high efficacy binning.

Engineered and manufactured by DENO LED Lighting — denoled.com, the custom LED strip manufacturer behind every long-run build in this series.

Long LED Strip Lights — Buyer Questions

How long can a long LED strip run be on a single power feed?

A standard 24V constant-voltage tape is limited to about 5 m before the far end visibly dims. DENO's long-run boards combine 2 oz to 3 oz copper, 24V or 48V input and per-segment constant-current ICs, which takes a single feed to 20 m, and up to 50 m on 48V builds, with no measurable fall-off between the first and last metre.

Do you supply extra long LED strip lights in 65.6 ft or 100 ft?

Yes. 65.6 ft (20 m) and 100 ft (30 m) are stock run lengths, and anything longer than 32 feet is supplied as one uncut board rather than two reels joined with a connector. Joints are the usual failure point on extra long LED strip lights, so removing them is the single biggest reliability gain on a large install.

Why do long strip lights get dimmer at the far end, and how is it fixed?

Copper resistance drops the supply voltage along the tape, so LEDs near the end of the run receive less drive current. Three fixes work together: raise the voltage (24V, 36V or 48V), raise the copper weight (2 oz or 3 oz), and add a linear constant-current IC per segment so each segment holds its current regardless of the local voltage it sees.

Which long outdoor LED strip lights are rated for wet locations?

Long outdoor LED strip lights are built IP65 silicone-coated, IP67 sleeved or IP68 fully potted, with DENO WAP™ conformal coating that stays clear instead of yellowing under UV. For facade and perimeter work the run length also has to survive thermal cycling, so outdoor boards use 3 oz copper and a wider PCB to spread heat.

What makes long lasting LED strip lights actually last?

Lifetime is decided by junction temperature and solder-joint fatigue, not by the LED bin. DENO specifies 99.9% pure electroplated copper for lower thermal resistance, gold-wire bonding, and derated drive current — L90 at 50,000 hours on standard architectural builds, backed by a 5-year warranty.

Can a long RGB or RGBIC strip run stay colour-consistent?

It can, provided each colour channel is current-regulated. On a plain long RGB LED strip the red die drops out first as voltage falls, so the far end shifts warm; a CC-regulated 24V colour board holds the mix over 15 m to 20 m. Addressable RGBIC runs additionally need data re-amplification roughly every 5 m.

Can long LED light strips be cut to an exact length for a room or kitchen?

Yes. Cut units run from 12.5 mm to 100 mm depending on voltage and density, so a run can be trimmed to a drawing dimension on site, and DENO also pre-cuts and pre-wires to length at the factory for room, cove and kitchen installations. Ask for the cut unit in the quote — it decides how closely the finished line matches the millwork.

Can you get LED strip lights longer than 32 feet in one run?

Yes — 32 feet (10 m) is where consumer tape stops, not where the physics stops. Past that the board needs constant-current regulation and 2 oz to 3 oz copper, and DENO supplies it as one uncut length with factory-fitted lead wires rather than two reels joined by a solderless connector, which would put the whole downstream current through a spring contact.

Should I specify a 65.6 ft or a 100 ft LED strip run?

65.6 ft (20 m) is the practical ceiling for a 24V constant-current board with 2 oz copper on a single-end feed, and it covers most cove and corridor jobs with one driver. 100 ft (30 m) moves to 36V or 48V with 3 oz copper, a bigger driver and usually a mid-point tap, because at 24V the current would be high enough for cable losses to matter.

When is a long RGBW LED strip better than RGB on a long run?

Whenever the same run also has to serve as everyday white light. Mixing white from three colour dies costs roughly twice the wattage for the same lux and renders skin and timber poorly — a real penalty over 20 m. RGBW adds a dedicated Ra 90+ white die at 2700K to 6500K, so white comes from a white source and the colour channels stay reserved for scenes.

Is 36V or 48V better for a long LED strip installation?

48V once a single run passes about 30 m, 36V between 20 m and 30 m or where a 48V driver is unavailable. Both stay inside SELV limits and both cut voltage drop sharply against 24V; the trade-off is the cut unit, which grows from roughly 50 mm at 24V to 100 mm at 36V and up to 166.6 mm at 48V.

Frequently asked questions

O que define uma Fita de LED para trechos ultralongos e quais são suas principais vantagens?

Uma Fita de LED para trechos ultralongos é projetada para operar continuamente em comprimentos estendidos, normalmente 10 metros ou mais, a partir de um único ponto de alimentação. Esse projeto reduz significativamente o número de pontos de injeção de alimentação, simplificando a fiação, minimizando a mão de obra de instalação e garantindo emissão luminosa uniforme em todo o comprimento, o que é crucial para projetos de iluminação arquitetônica e comercial de grande escala.

Qual é o comprimento contínuo máximo disponível para as Fitas de LED para trechos ultralongos da DENO LED?

A DENO LED oferece Fitas de LED para trechos ultralongos em comprimentos contínuos de até 50 metros, dependendo do modelo específico e dos requisitos de potência. Essa capacidade de comprimento estendido é obtida por meio de um projeto de circuito otimizado e FPCB de alta qualidade, garantindo queda de tensão mínima e brilho consistente em todo o segmento. As fichas técnicas de cada modelo fornecem as especificações precisas de comprimento contínuo máximo.

Como a DENO LED lida com a queda de tensão e garante brilho uniforme em Fitas de LED para trechos ultralongos?

A DENO LED reduz a queda de tensão em Fitas de LED para trechos ultralongos por meio de diversas medidas de projeto: utilização de sistemas de 24V ou tensão superior, emprego de trilhas de cobre mais espessas no FPCB eletrodepositado em processo rolo a rolo e otimização do layout do circuito. Essas medidas garantem distribuição consistente de corrente e brilho uniforme em todo o comprimento da fita, mantendo o fluxo luminoso e a Temperatura de Cor (CCT) especificados.

A DENO LED pode fornecer opções de personalização para Fitas de LED para trechos ultralongos, como comprimentos ou temperaturas de cor específicos?

Sim, a DENO LED oferece amplas opções de personalização OEM/ODM para Fitas de LED para trechos ultralongos. Isso inclui comprimentos personalizados específicos, uma ampla faixa de Temperatura de Cor (CCT) e diversos graus de proteção IP. Também podemos integrar conectores específicos ou soluções de montagem para atender aos requisitos particulares do projeto. Consulte nossa equipe de vendas com as especificações do seu projeto para obter detalhes sobre as possibilidades de personalização e os prazos de entrega.

O que limita o comprimento de um trecho de Fita de LED?

A queda de tensão e a corrente no condutor, não o LED em si. Uma Fita de LED para trechos longos combina baixa potência por metro, cobre de 2 oz ou mais espesso e uma tensão de barramento mais alta, como 24V, 36V ou 48V, para alcançar 20 m ou mais a partir de um único ponto de alimentação, mantendo a queda dentro de 3 por cento.