Neon Flexível de LED 360° — Neon Redondo | DENO

Outdoor & façade exposure

Specify for permanent exterior installation above the waterline (IP67).

The silicone is injection moulded onto the FPCB in one shot, so there is no glued cover to open up after a winter of thermal cycling — the failure mode PVC neon rope light shows in its second outdoor summer. UV-stabilised silicone keeps its colour instead of yellowing, and the body stays elastic from −30 °C to +80 °C, so a façade run installed in summer will not go brittle in a January frost. Feed with low-voltage DC and plan short runs per feed to hold end-of-run brightness across a long elevation.

• Sealed silicone body
• UV-stable silicone, −30 °C to +80 °C
• Low thermal load

Pools, spas & wet areas

Suitable for pool surrounds, spa ceilings and steam-adjacent joinery — not for submersion.

IP67 covers rain, splash, wash-down and steam — pool decks, shower reveals, sauna ceilings and spa coves — but the body is not intended to sit under water. Mount it above the waterline in an aluminium groove so condensate drains away from the feed joint, run low-voltage DC for wet-zone safety, and choose the IP68 variant where the channel can flood.

• IP67 — splash and rain, not submersion
• low-voltage DC
• Moulded end cap and feed joint

Architectural contour & signage

Bends in every direction — the body is a round tube at free-form radii — the right pick for handrails, tree wraps, columns and free-form sculptural runs.

360° round LED neon flex takes its curve in every direction — the body is a round tube, which is what decides whether a shape is possible without cutting and re-soldering. At free-form radii the outside of the curve stays evenly lit: the LED pitch is matched to the diffuser depth so you read a continuous line of light rather than dots, even at 30 cm. Printed cut marks with indexed solder pads underneath let a sign maker shorten a letter stroke on site and re-seal it, and mounting clips, aluminium grooves and moulded bend grooves cover surface, recessed and free-form fixing.

• Compact silicone body
• Bend radius free-form radii
• Dot-free diffusion

What is a 360 degree LED neon flex?

A 360 degree LED neon flex is a round silicone body — typically 20 mm to 25 mm in diameter — with LEDs mounted so light leaves the whole circumference instead of one face. It replaces the old round neon rope light in exposed applications: suspended rings, handrails, tree wraps and free-standing sculptural lines where the viewer sees the tube from every side.

• Related series LED neon strip and neon flex family
• Related series single-face top bend alternatives
• Product DL-NFT22D1 360° round neon flex

How is a round LED neon tube light different from a rope light?

A traditional rope light uses spaced LEDs inside a clear PVC tube, so you see dots and the PVC yellows outdoors. A round LED neon tube light uses a dense FPCB inside a moulded diffusing silicone body: continuous light, no visible dots, no yellowing, and a proper IP67 seal instead of a crimped cap.

• Guide silicone versus PVC ageing data
• Related series dense boards that remove the dot pattern

What beam angle does an omnidirectional LED neon give?

The circular section produces a true 360° distribution with no dark seam along the back, unlike a top bend body that emits over roughly 120–160°. For a suspended ring or a wrapped column, the omnidirectional LED neon keeps brightness constant as the observer walks around it — the reason it is specified for retail atria and event structures.

• Guide calculate flux and illuminance for a run
• Guide photometric reference data
• Product DL-FCN25 omnidirectional neon flex

Can a 360 neon flex be bent in any direction?

Yes — a round body has no preferred bend axis, so it takes horizontal and vertical curves alike, typically down to R60–R80 mm depending on diameter. That freedom is why circular neon flex is chosen for free-form artwork and signage scripts that mix directions inside one continuous run.

• Related series side bend bodies for planar curves
• Guide pre-bent neon assemblies made to drawing

How is a 360° neon flex mounted?

Three common methods: suspension by stainless wire through moulded eyelets, saddle clips at 300–500 mm centres, and a semi-circular aluminium groove where only part of the tube shows. Because the body emits all round, mounting hardware is kept slim so it does not cast a shadow line along the run.

• Related series six neon mounting methods explained
• Guide ask DENO for a mounting drawing

Is 360 neon available in RGB or tunable white?

Yes. The round platform accepts single colour 2700–6500K, tunable white, RGB and RGBW light engines, plus addressable builds for chase and gradient effects. Control is standard constant-voltage PWM, DALI DT8 or DMX512 through a decoder, so it drops into an existing architectural control system.

• Related series RGBW light engines
• Related series addressable pixel builds for chase effects