What is a constant current LED strip?

A constant current LED strip carries a linear CC driver IC on the board that holds a fixed current through each segment regardless of the input voltage seen at that point. Brightness therefore stays flat along the run, instead of falling off with voltage drop the way a plain constant-voltage strip does.

Constant current vs constant voltage LED strip — which is better?

Constant voltage is cheaper and fine for short runs under 3 m. Constant current is the right choice whenever the run is long, the copper is thin, the input voltage is unstable, or the installation is camera-facing — the IC absorbs supply variation and keeps every metre at the same luminous flux.

Can a constant current LED strip be powered from both ends or mid-feed?

Yes. Because regulation happens per segment, DENO's CC boards accept single-end, both-ends and any mid-strip tap. Both-ends and mid-feed wiring halve the effective feed distance, which is how a single driver covers a long corridor or perimeter cove.

Does a constant current LED strip dim without flicker?

It does when the driver is matched to it. Linear CC ICs dim smoothly on PWM down to about 1%, and at 16 kHz+ PWM the run is flicker-free on camera (low Pst LM and SVM). Analogue dimming of a CC board is not recommended below 20% because the IC needs headroom.

How long can a constant current LED strip run be?

Up to 20 m and beyond on 24V or 48V builds with 2 oz copper, versus 5 m for a comparable constant-voltage board. The practical limit becomes the copper's current-carrying capacity and thermal design rather than perceived brightness fall-off.

Can I order a custom constant current LED strip?

Yes — segment length, drive current, voltage, LED density, CCT/CRI, PCB width and copper weight are all configurable, and CC regulation can be combined with high-density, ultra-narrow or full-spectrum layouts on the same board.

Fita de LED 2835 de Corrente Constante, Alto Fluxo Luminoso e Alta Eficácia Luminosa (#5932)

10mm · 24V · 112LEDs · 71.4corte

Model: 5932

5932 10mm | 24V | 112LEDs | 71.4corte | #5932 | Fita de LED 2835 de Corrente Constante, Alto Fluxo Luminoso e Alta Eficácia Luminosa — 24V, cuttable every 71.4mm, 10mm FPCB width, 2835 LEDs, 112 LEDs/m, IP20

Visão Geral

10mm | 24V | 112LEDs | 71.4cut | #5932 | Fita de LED 2835 de Corrente Constante, Alto Fluxo Luminoso e Alta Eficácia Luminosa faz parte da série DENO de Fitas SMD C.C. (Reguladas por IC), desenvolvida com base em Fita de LED com IC de corrente constante. Especificações principais: 2835, 112 LEDs/m, DC 24V, PCB de 10, FPCB de cobre de 3oz, corte a cada 8LEDs/71.4mm. Cada rolo é produzido na linha rolo a rolo da DENO com FPCB de cobre com pureza de 99.9% e é fornecido em conformidade com CE, UL e RoHS para projetos arquitetônicos, de varejo e de hotelaria. Configurações OEM e ODM de comprimento, temperatura de cor e impermeabilização estão disponíveis sob consulta.

Descrição

Projetada com 112 chips SMD 2835 por metro, esta Fita de LED de corrente constante de 24V proporciona desempenho uniforme para instalações de iluminação arquitetônica de alto padrão. A placa de circuito de 10mm de largura apresenta um projeto robusto com folha de cobre de 3oz para garantir estabilidade térmica ideal até uma temperatura máxima de 75°C. Estruturas de terminais dos LEDs em cobre puro durável, combinadas com encapsulamento com fio de ouro de 99.9% de pureza, protegem eficazmente os emissores contra esforços mecânicos durante a montagem. Pontos de corte precisos espaçados a cada 71.4mm, com passo de 8.9mm e capacidade de dimerização, permitem iluminação uniforme em um ângulo de abertura de 120 graus. Fornecida em trechos de comprimento máximo de 5M, com diâmetro de curvatura de 60mm, nossa oferta no atacado diretamente da fábrica para projetos atende a instalações comerciais personalizadas.

High Efficacy Led Strip Lights built for high light efficacy smd strips projects.

Especificações

LED QTY	112 LEDs/m
PART NO	DL-F28A56V24-5932-*
SMD TYPE	2835
CUTTABLE UNIT	8LEDs/71.4mm
DIMMABLE	Yes
IP RATING	IP20
LED PITCH	8.9mm
PCB WIDTH	10
BEAM ANGLE	120°
RUN LENGTH	5M
COPPER FOIL	3oz
ON OFF TIMES	10000（test times）
POWER RANGE	3.4~20W
CIRCUIT TYPE	C.C.
INPUT VOLTAGE	DC 24V
MIN BEND DIAMETER	Φ60mm
OPERATING TEMPERATURE	-25~40°C;Tc：75°C（max）

Aplicações

Cove, wall-wash & perimeter lighting — Coves, recesses, wall-wash details and ceiling perimeters where a continuous, uniform line of light is required.
Showroom & hospitality display lighting — Shelving, display cases, reception desks and signage backlighting in shops, showrooms and hospitality spaces.
Kitchen & wardrobe under-cabinet lighting — Kitchen, wardrobe and furniture task lighting where the strip stays hidden and only the light is seen.

Acessórios recomendados e peças compatíveis

DL-1003 — 19.1x8mm Surface Mount LED Channel — Dotless Aluminum Profile for 240 LEDs/m Strip: Accepts LED strips up to 10mm wide.
DL-1103-1 — 16x13mm Surface Mount LED Channel — Aluminum Profile for 10mm LED Strip: Accepts LED strips up to 10mm wide.
DL-1510 HX-F — 15x9.9mm Recessed LED Channel with Flange — Flush Mount Aluminum Profile: Accepts LED strips up to 10mm wide.
DN-PSU-100 — 24V 100W Class-2 LED Driver · High Efficiency: Matches the 24V DC input of this strip; size the driver with at least 20% headroom over total load.
DN-PSU-150 — 24V 150W Class-2 LED Driver · Premium: Matches the 24V DC input of this strip; size the driver with at least 20% headroom over total load.
DN-PSU-60 — 24V 60W Class-2 LED Driver · Constant Voltage: Matches the 24V DC input of this strip; size the driver with at least 20% headroom over total load.
V1 — 5-36VDC 1-Channel * 8A RF+Push Dimming Controller | V1: Matched by input voltage range and colour channels.

Solicite um orçamento para #5932

A DENO LED é uma fabricante de fitas de LED com sede em Shenzhen e base de produção própria em Foshan. Envie-nos o comprimento do trecho, tensão, CCT/IRC e grau de proteção IP que você precisa e nossa equipe de engenharia responderá com uma ficha técnica, diagrama de fiação e preço — OEM/ODM e projetos totalmente personalizados incluídos.

WhatsApp para nossa engenharia Formulário de contato Capacidade OEM / ODM

Garantia: 5 anos
Prazo de entrega: Placas padrão: amostras a partir de 1 dia útil · personalizadas: 3–5 dias úteis · nova FPCB: 1–3 semanas · produção 1–2 semanas após aprovação da amostra
Conformidade: CE · ETL · UL · RoHS
Fio de ligação: Ouro puro 99,99%
Folha de cobre: FPCB de cobre puro 99,9%
Serviços: CCT, IRC, largura de PCB, unidade de corte e embalagem personalizadas — amostras e produção em massa de uma única fábrica.

Desempenho Fotométrico — Matriz de Eficácia CCT × IRC (CRI)

Peak measured luminous efficacy: 216 lm/W at 4000K, Ra 80, ErP energy class B (Grade DN (1st Tier)).

All values are measured at the stated power density and ambient 25 °C, reported as luminous efficacy in lumens per watt (lm/W), luminous flux per metre (lm/m) and the corresponding EU ErP (2019/2015) energy class.

Grade KE (3rd Tier)

Grade KE (3rd Tier) — measured at 3.4 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1900 K	135.7 lm/W	461.5 lm/m	D	108.8 lm/W	369.9 lm/m	F	—	—	—
2300 K	151.3 lm/W	514.4 lm/m	D	121.2 lm/W	412.2 lm/m	E	98.2 lm/W	333.9 lm/m	F
2700 K	163 lm/W	554.1 lm/m	C	131.5 lm/W	447.2 lm/m	E	106.6 lm/W	362.6 lm/m	F
3000 K	171.2 lm/W	582.2 lm/m	C	138.9 lm/W	472.4 lm/m	D	113 lm/W	384.1 lm/m	E
3500 K	173.7 lm/W	590.6 lm/m	C	141.7 lm/W	481.9 lm/m	D	116.6 lm/W	396.5 lm/m	E
4000 K	178.9 lm/W	608.1 lm/m	C	144.7 lm/W	492.1 lm/m	D	119.4 lm/W	406 lm/m	E
5000 K	178.5 lm/W	607 lm/m	C	144.7 lm/W	492.1 lm/m	D	119.4 lm/W	406 lm/m	E
6500 K	171.2 lm/W	582.2 lm/m	C	138.9 lm/W	472.4 lm/m	D	115.3 lm/W	392 lm/m	E

Grade KE (3rd Tier)

Grade KE (3rd Tier) — measured at 6.7 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1900 K	132.6 lm/W	888.5 lm/m	E	106.3 lm/W	712.2 lm/m	F	—	—	—
2300 K	147.8 lm/W	990.4 lm/m	D	118.5 lm/W	793.7 lm/m	E	96 lm/W	643.2 lm/m	F
2700 K	159.2 lm/W	1066.9 lm/m	D	128.5 lm/W	861.1 lm/m	E	104.2 lm/W	698.2 lm/m	F
3000 K	167.3 lm/W	1121 lm/m	C	135.8 lm/W	909.6 lm/m	D	110.4 lm/W	739.6 lm/m	E
3500 K	169.7 lm/W	1137.2 lm/m	C	138.5 lm/W	927.8 lm/m	D	114 lm/W	763.5 lm/m	E
4000 K	174.8 lm/W	1170.9 lm/m	C	141.4 lm/W	947.5 lm/m	D	116.7 lm/W	781.8 lm/m	E
5000 K	174.4 lm/W	1168.8 lm/m	C	141.4 lm/W	947.5 lm/m	D	116.7 lm/W	781.9 lm/m	E
6500 K	167.3 lm/W	1121 lm/m	C	135.8 lm/W	909.6 lm/m	D	112.7 lm/W	755.1 lm/m	E

Grade KE (3rd Tier)

Grade KE (3rd Tier) — measured at 10 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1900 K	129.6 lm/W	1295.7 lm/m	E	103.9 lm/W	1038.6 lm/m	F	—	—	—
2300 K	144.4 lm/W	1444.3 lm/m	D	115.7 lm/W	1157.5 lm/m	E	93.8 lm/W	938 lm/m	F
2700 K	155.6 lm/W	1555.9 lm/m	D	125.6 lm/W	1255.8 lm/m	E	101.8 lm/W	1018.2 lm/m	F
3000 K	163.5 lm/W	1634.8 lm/m	C	132.6 lm/W	1326.5 lm/m	E	107.9 lm/W	1078.6 lm/m	F
3500 K	165.8 lm/W	1658.4 lm/m	C	135.3 lm/W	1353.1 lm/m	D	111.3 lm/W	1113.4 lm/m	E
4000 K	170.8 lm/W	1707.5 lm/m	C	138.2 lm/W	1381.8 lm/m	D	114 lm/W	1140.1 lm/m	E
5000 K	170.4 lm/W	1704.4 lm/m	C	138.2 lm/W	1381.8 lm/m	D	114 lm/W	1140 lm/m	E
6500 K	163.5 lm/W	1634.8 lm/m	C	132.6 lm/W	1326.5 lm/m	E	110.1 lm/W	1101 lm/m	E

Grade DL (2nd Tier)

Grade DL (2nd Tier) — measured at 3.4 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	158.1 lm/W	537.5 lm/m	D	127 lm/W	431.7 lm/m	E	—	—	—
2300 K	176.1 lm/W	598.8 lm/m	C	141.5 lm/W	480.9 lm/m	D	114.6 lm/W	389.6 lm/m	E
2700 K	186.4 lm/W	633.8 lm/m	B	153 lm/W	520.3 lm/m	D	124.1 lm/W	421.8 lm/m	E
3000 K	198.2 lm/W	674 lm/m	B	161.1 lm/W	547.7 lm/m	C	130.9 lm/W	445.2 lm/m	E
3500 K	201.1 lm/W	683.8 lm/m	B	163.9 lm/W	557.2 lm/m	C	134.9 lm/W	458.7 lm/m	E
4000 K	207.6 lm/W	705.7 lm/m	B	167.9 lm/W	570.7 lm/m	C	138.6 lm/W	471.1 lm/m	D
5000 K	207.3 lm/W	705 lm/m	B	167.7 lm/W	570.3 lm/m	C	138.4 lm/W	470.6 lm/m	D
6500 K	190.2 lm/W	646.6 lm/m	B	161 lm/W	547.4 lm/m	C	133.6 lm/W	454.2 lm/m	E

Grade DL (2nd Tier)

Grade DL (2nd Tier) — measured at 6.7 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	154.5 lm/W	1034.9 lm/m	D	124.1 lm/W	831.2 lm/m	E	—	—	—
2300 K	172.1 lm/W	1153 lm/m	C	138.2 lm/W	926 lm/m	D	112 lm/W	750.4 lm/m	E
2700 K	182.1 lm/W	1220.4 lm/m	C	149.5 lm/W	1001.9 lm/m	D	121.2 lm/W	812.2 lm/m	E
3000 K	193.7 lm/W	1297.7 lm/m	B	157.4 lm/W	1054.6 lm/m	D	127.9 lm/W	857.2 lm/m	E
3500 K	196.5 lm/W	1316.7 lm/m	B	160.1 lm/W	1072.9 lm/m	C	131.8 lm/W	883.2 lm/m	E
4000 K	202.8 lm/W	1358.8 lm/m	B	164 lm/W	1098.9 lm/m	C	135.4 lm/W	907 lm/m	D
5000 K	202.6 lm/W	1357.4 lm/m	B	163.9 lm/W	1098.2 lm/m	C	135.2 lm/W	905.8 lm/m	D
6500 K	185.8 lm/W	1245 lm/m	B	157.3 lm/W	1053.9 lm/m	D	130.6 lm/W	875 lm/m	E

Grade DL (2nd Tier)

Grade DL (2nd Tier) — measured at 10 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	150.9 lm/W	1509.3 lm/m	D	121.2 lm/W	1212.1 lm/m	E	—	—	—
2300 K	168.1 lm/W	1681.4 lm/m	C	135 lm/W	1350.4 lm/m	D	109.4 lm/W	1094 lm/m	F
2700 K	178 lm/W	1779.8 lm/m	C	146.1 lm/W	1461.1 lm/m	D	118.4 lm/W	1184.5 lm/m	E
3000 K	189.2 lm/W	1892.5 lm/m	B	153.8 lm/W	1538 lm/m	D	125 lm/W	1250 lm/m	E
3500 K	192 lm/W	1920.1 lm/m	B	156.5 lm/W	1564.6 lm/m	D	128.8 lm/W	1287.9 lm/m	E
4000 K	198.2 lm/W	1981.6 lm/m	B	160.3 lm/W	1602.5 lm/m	C	132.3 lm/W	1322.8 lm/m	E
5000 K	198 lm/W	1979.6 lm/m	B	160.1 lm/W	1601.5 lm/m	C	132.1 lm/W	1321 lm/m	E
6500 K	181.6 lm/W	1815.6 lm/m	C	153.7 lm/W	1536.9 lm/m	D	127.6 lm/W	1276 lm/m	E

Grade DN (1st Tier)

Grade DN (1st Tier) — measured at 3.4 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	169.2 lm/W	575.1 lm/m	D	142.7 lm/W	485.1 lm/m	E	—	—	—
2300 K	184.5 lm/W	627.2 lm/m	C	159.3 lm/W	541.6 lm/m	D	129 lm/W	438.6 lm/m	E
2700 K	198.8 lm/W	676 lm/m	C	172.4 lm/W	586 lm/m	D	139.7 lm/W	474.9 lm/m	E
3000 K	208.8 lm/W	709.9 lm/m	B	181.9 lm/W	618.5 lm/m	C	147.9 lm/W	503 lm/m	D
3500 K	211.9 lm/W	720.4 lm/m	B	185.9 lm/W	631.9 lm/m	C	153 lm/W	520.1 lm/m	D
4000 K	216 lm/W	734.3 lm/m	B	186.9 lm/W	635.6 lm/m	C	154.3 lm/W	524.5 lm/m	D
5000 K	215.6 lm/W	733.2 lm/m	B	188.1 lm/W	639.6 lm/m	C	155.2 lm/W	527.7 lm/m	D
6500 K	206.8 lm/W	703 lm/m	B	179.8 lm/W	611.2 lm/m	C	149.2 lm/W	507.3 lm/m	D

Grade DN (1st Tier)

Grade DN (1st Tier) — measured at 6.7 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	165.3 lm/W	1107.3 lm/m	D	139.4 lm/W	934.1 lm/m	E	—	—	—
2300 K	180.2 lm/W	1207.6 lm/m	C	155.6 lm/W	1042.8 lm/m	D	126.1 lm/W	844.9 lm/m	E
2700 K	194.3 lm/W	1301.6 lm/m	C	168.4 lm/W	1128.4 lm/m	D	136.5 lm/W	914.5 lm/m	E
3000 K	204 lm/W	1366.8 lm/m	B	177.7 lm/W	1190.8 lm/m	C	144.5 lm/W	968.5 lm/m	E
3500 K	207 lm/W	1387.2 lm/m	B	181.6 lm/W	1216.7 lm/m	C	149.5 lm/W	1001.4 lm/m	D
4000 K	211 lm/W	1413.8 lm/m	B	182.6 lm/W	1223.8 lm/m	C	150.7 lm/W	1009.9 lm/m	D
5000 K	210.7 lm/W	1411.7 lm/m	B	183.8 lm/W	1231.5 lm/m	C	151.6 lm/W	1015.7 lm/m	D
6500 K	202 lm/W	1353.5 lm/m	B	175.6 lm/W	1176.8 lm/m	C	145.8 lm/W	976.9 lm/m	D

Grade DN (1st Tier)

Grade DN (1st Tier) — measured at 10 W/m: luminous efficacy (lm/W), luminous flux (lm/m) and ErP energy class per CCT and CRI grade.
CCT (K)	Ra 80 — Luminous Efficacy (lm/W)	Ra 80 — Luminous Flux (lm/m)	Ra 80 — ErP Energy Class	Ra 90 — Luminous Efficacy (lm/W)	Ra 90 — Luminous Flux (lm/m)	Ra 90 — ErP Energy Class	Full Spectrum (Ra 95+) — Luminous Efficacy (lm/W)	Full Spectrum (Ra 95+) — Luminous Flux (lm/m)	Full Spectrum (Ra 95+) — ErP Energy Class
1800 K	161.5 lm/W	1614.9 lm/m	D	136.2 lm/W	1362.3 lm/m	E	—	—	—
2300 K	176.1 lm/W	1761.1 lm/m	C	152.1 lm/W	1520.8 lm/m	D	123.2 lm/W	1232 lm/m	E
2700 K	189.8 lm/W	1898.2 lm/m	C	164.6 lm/W	1645.6 lm/m	D	133.4 lm/W	1333.6 lm/m	E
3000 K	199.3 lm/W	1993.3 lm/m	C	173.7 lm/W	1736.6 lm/m	C	141.2 lm/W	1412.4 lm/m	E
3500 K	202.3 lm/W	2022.9 lm/m	B	177.4 lm/W	1774.4 lm/m	C	146 lm/W	1460.4 lm/m	D
4000 K	206.2 lm/W	2061.8 lm/m	B	178.5 lm/W	1784.6 lm/m	C	147.3 lm/W	1472.7 lm/m	D
5000 K	205.9 lm/W	2058.7 lm/m	B	179.6 lm/W	1795.9 lm/m	C	148.2 lm/W	1482 lm/m	D
6500 K	197.4 lm/W	1973.8 lm/m	C	171.6 lm/W	1716.1 lm/m	D	142.4 lm/W	1424 lm/m	E

Recommended LED Channels

Mount this LED strip in a DENO LED aluminum profile for heat dissipation, physical protection and diffused, dot-free output.

This strip is 10mm wide, so it needs a channel with at least 12mm inner width (10mm + 2mm clearance). Every profile below meets that.

Modelos relacionados nesta série

See every model in SMD LED Strip Series or narrow to Ic. Compare wattage, lumen output and run length in the ProCalc parameter library, or request OEM/ODM pricing on the custom manufacturing page.

Perguntas Frequentes

Quais são as principais especificações do 5932?

5932: 2835, 112 LEDs/m, DC 24V, PCB de 10, FPCB de cobre de 3oz, corte a cada 8LEDs/71.4mm. Dados fotométricos completos, diagramas de ligação e relatórios de ensaio estão disponíveis na seção de downloads desta página.

O que diferencia a construção desta Fita de LED com IC de corrente constante?

Ela é construída como uma Fita de LED com IC de corrente constante sobre FPCB de cobre de 3oz, com uma unidade de corte de 8LEDs/71.4mm e espaçamento entre LEDs de 8.9mm, mantendo seu desempenho elétrico e mecânico onde fitas padrão falham.

A DENO pode personalizar esta Fita de LED com IC de corrente constante para um projeto?

Sim. A DENO fabrica a série de Fitas SMD C.C. (Reguladas por IC) como fornecedora OEM e ODM: comprimento do rolo, temperatura de cor, classe de IRC (CRI), largura da PCB, impermeabilização e identificação com marca própria podem ser especificados. Solicite um Orçamento para obter o prazo de entrega e os preços do projeto.

Uma Fita de LED de corrente constante realmente elimina a queda de tensão?

A tensão ainda cai ao longo do cobre, mas o IC de corrente constante de cada segmento mantém a corrente dos LEDs fixa até que a tensão local fique abaixo do seu limite mínimo de regulação. Assim, o brilho permanece uniforme de ponta a ponta, e a alimentação pode ser injetada em uma extremidade, em ambas ou em qualquer ponto intermediário do trecho.

Quanto uma Fita de LED de alta eficácia pode reduzir o consumo de energia?

Passar de uma fita típica de 100 lm/W para uma Fita de LED de alto fluxo luminoso de 180 a 200 lm/W reduz aproximadamente pela metade a potência necessária para o mesmo fluxo luminoso. Em um trecho comercial longo, isso também reduz a potência necessária do Driver / Fonte de Alimentação e ajuda a instalação a atingir uma classe energética ErP melhor.

Engineering & selection guide

Bending limits, IP selection, voltage drop, cutting and the full buyer Q&A for this family are kept on the series page.

constant current LED strip series — Constant Current LED Strip — Buyer Questions
LED strip engineering selection handbook